You’re attempting to connect Netgear WiFi extender to a new CenturyLink router, then. Yet it appears to be nearly impossible to connect the gadgets. You will benefit from reading this blog post. How? The complete procedure to connect Netgear WiFi extender to a new CenturyLink router is covered in this post. Go through this blog to learn some easy ways to prevent problems with connectivity.
Let’s connect Netgear WiFi extender to a new CenturyLink router.
Now that you have a new CenturyLink router in lieu of your old one, you are attempting to connect it to the extension. We must inform you that your extender is not prepared for the connection since you are unable to get the devices connected. What is meant by that? User is not able to connect Netgear WiFi extender to a new CenturyLink router.
The Netgear WiFi extender was previously connected to the router. The extender is still using the settings from the old router. To get it ready to connect to the new router, you must first wipe them. stay in touch You need to reset the WiFi extender in order to finish this procedure.
How Can the Netgear WiFi Extender Be Reset?
Resetting the Netgear extender involves removing the existing configuration settings and returning it to its original factory defaults. Follow the guidelines provided below to reset your extender:
- Except for the power cable, unplug all cables attached to the Netgear WiFi extender.
- Make that the extension is plugged into a functional power outlet and that it is completely charged.
- Now, search your extender for the Reset button. The button is often located inside a hole that says “Factory Reset” or “Reset.”
- For a minimum of ten seconds, push and hold the Reset button with the assistance of a pointed or sharp item.
- After rebooting, the extender will resume its factory configuration.
It’s now possible to connect Netgear WiFi extender to a new CenturyLink router. Verify that the router is already configured with the DSL gateway or internet modem.
How to connect Netgear wifi extender to a new CenturyLink router?
- Move the Netgear WiFi router and extension closer to one another.
- Connect the extender’s Internet port to the router’s LAN port using a LAN cable.
- After plugging in and turning on the router, switch on the extender. To prevent any issues, it is advised to follow the same order.
- Now, link your phone, PC, or laptop to the network of the extender.
- Either use a LAN wire to connect your PC, or use the default SSID Netgear_Ext to join your device to the extender’s WiFi network.
- Open a browser to go straight to the Netgear extender setup page. In the event that the configuration page fails to load automatically, try 192.168.1.250 or mywifiext.net.
- Proceed with following the setup instructions as they show on the screen. When prompted, choose the SSID of the CenturyLink router in order to join the extender to its network.
- You’ve successfully established a connection between your Netgear extender and your new CenturyLink router.
Adjust the Extender
Change the position of your Netgear WiFi extender. Select an area to expand the network range of the router. That has to be, though, inside the router’s network range.
Check for Updates in the extender’s Firmware
Make sure to upgrade the firmware on the Netgear extender as well as on the CenturyLink router. Update both of the devices’ firmware versions by using the IP to log in and access them. For CenturyLink routers, 192.168.0.1 is the default IP address. If the devices share an IP address, the IP may be modified to prevent IP conflict. In the event that the default IP address is inoperative, verify the one that is originally issued to your router. Perhaps your router has been issued a different IP, such as 10.0.0.1. while The IP address for Netgear extender is 192.168.1.250.
Change your passwords
You are requested to update the WiFi and admin passwords for the Netgear extender throughout the setup process. Update the passwords right away if you didn’t change them during setup. This is to guarantee your network’s security.
Now, let’s wrap it up.
It is simple to connect Netgear WiFi extender to a new CenturyLink router to a by following the methods covered in this document. We have assisted you in removing the hindrance that was keeping the two devices from connecting. Additionally, we’ve given you instructions on what to do once the extension and router are configured. Here, we conclude our informative post in the hopes that the extender is now prepared to extend the WiFi of the new router.
